How Much Does It Cost to Replace a Well Pump?
$1,500 – $4,000
National average: $1,900 installed
Estimate your cost
Adjust the options for a tailored ballpark — figures and the regional adjustment are approximate estimates. Always confirm with local quotes before you budget.
For homes on well water, the pump is what delivers every drop — and when it fails, you have no water until it’s fixed. Replacement costs $1,500 to $4,000 installed in 2026, averaging around $1,900, with well depth and pump type driving the price.
What you’re paying for
The pump itself is part of it, but you’re also paying for the drop pipe and wiring that run down the well, the labor to pull the old pump and set the new one, and sometimes a new pressure tank. On deep wells, the pull is the hard part — which is why depth matters so much.
Cost by pump type and depth
The table below shows typical installed pricing by pump type and well depth.
Jet vs. submersible
Jet pumps sit above ground and draw water up from shallow wells — simpler and cheaper. Submersible pumps sit at the bottom of deep wells and push water up — the most common type, and pricier because of the depth and equipment needed to service them. Your well determines which you have.
Don’t forget the pressure tank
The pump works with a pressure tank that stores water and maintains pressure. If yours is also failing (rapid pump cycling is a clue), replacing both at once ($300–$800 for the tank) saves a second service call and protects the new pump from short-cycling.
How to save on well pump replacement
- Replace the pressure tank at the same time if it’s near end of life.
- Get multiple quotes from well specialists — depth and access pricing varies.
- Address it before total failure to avoid emergency rates and being without water.
- Keep records of your well depth and pump specs to speed future service.
| Component | Typical range | Notes |
|---|---|---|
| Pump unit | $400 – $2,500 | — |
| Drop pipe & wiring | $200 – $1,500 | — |
| Labor (pull & install) | $300 – $1,500 | — |
| Pressure tank (if needed) | $300 – $800 | — |
| Permit / inspection | $0 – $300 | — |
| Option | Typical range | Notes |
|---|---|---|
| Jet pump (shallow well) | $400 – $1,400 | — |
| Submersible — 200-ft well | $1,800 – $3,000 | Most common |
| Submersible — 400-ft well | $4,000 – $6,000 | — |
| Pressure tank (add) | $300 – $800 | — |
What affects the price
- Well depth The single biggest driver — deeper wells need more pipe, wire, and labor to pull and reset the pump.
- Pump type Jet pumps for shallow wells are cheapest; submersible pumps for deep wells cost more.
- Pressure tank If the pressure tank is also failing, replacing it adds $300–$800.
- Pipe & wiring condition Old drop pipe and wiring are often replaced along with the pump.
Frequently asked questions
- How much does it cost to replace a well pump?
- Most replacements run $1,500–$4,000 installed, averaging about $1,900. A shallow-well jet pump can be $400–$1,400, while a submersible in a deep well runs $1,800–$6,000.
- Jet pump vs. submersible — what's the difference?
- Jet pumps sit above ground and pull water from shallow wells (cheaper). Submersible pumps sit down in the well and push water up from deep wells (more common, pricier).
- What are the signs of a failing well pump?
- No water, sputtering faucets, low or fluctuating pressure, the pump running constantly, or higher electric bills all point to a failing pump or pressure tank.
- How long does a well pump last?
- Submersible pumps last 8–15 years; jet pumps 10+ years. Sediment, cycling, and water chemistry affect lifespan.
- Can I replace a well pump myself?
- A shallow-well jet pump is feasible for the handy. Pulling a submersible pump from a deep well requires special equipment and is a job for a well professional.
- Why does well depth matter so much?
- A deeper pump means more drop pipe and wire to buy and a harder, longer pull to remove the old one — roughly $500–$1,000 more per additional 100 feet.
How we estimate: ranges reflect typical U.S. pricing for materials and professional installation, compiled and cross-checked against the current (2026) industry sources listed below (see our data & methodology). Your actual cost depends on your location, project size, material grade, and local labor rates — always get multiple written quotes before you commit.
Sources
Cost ranges on this page were checked against current (2026) data from these industry sources: